Installation Guide
Professional setup instructions for your solar-powered deer repellent. Complete installation in just 5 minutes with no tools required.
Step-by-Step Installation
Follow these simple steps for optimal deer deterrent performance
Choose the Perfect Location
Strategic placement is key to maximum effectiveness
Instructions:
- Select area 3-4 feet above ground level
- Ensure clear line of sight to protected area
- Face sensor toward the garden/lawn to protect
- Solar panel should face south for optimal charging
- Avoid areas with dense foliage blocking the sensor
Pro Tips:
- • For gardens: Place at perimeter facing inward
- • For driveways: Mount on post or fence nearby
- • For large areas: Consider multiple units for overlap
Mount the Device
Two mounting options included for any situation
Instructions:
- Ground stake: Push firmly into soil until stable
- Wall bracket: Use included screws for fence/wall mounting
- Ensure device is level and secure
- Check that solar panel faces upward
- Verify sensor has unobstructed view
Pro Tips:
- • Ground stake works best in soft soil
- • Use wall bracket for hard surfaces or windy areas
- • Tilt solar panel slightly south if possible
Select Working Mode
Choose the right mode for your specific situation
Instructions:
- Mode 1: Ultrasonic only - Quiet operation
- Mode 2: LED flash only - Visual deterrent
- Mode 3: Both ultrasonic and LED - Maximum effect
- Mode 4: Random pattern - Prevents habituation
- Mode 5: 24/7 activation - Continuous protection
Pro Tips:
- • Mode 3 recommended for most deer problems
- • Use Mode 1 in residential areas to avoid LED flashing
- • Mode 4 best for persistent deer that adapt quickly
Test the System
Verify everything is working correctly
Instructions:
- Walk in front of sensor from 10-15 feet away
- LED should flash when motion is detected
- Check detection angle by walking side to side
- Verify solar panel is receiving sunlight
- Confirm battery indicator shows charge
Pro Tips:
- • Test during different times of day
- • Have someone watch the LED while you move around
- • Ultrasonic sound is inaudible - LED confirms activation
Optimize Performance
Fine-tune for maximum deer deterrent effectiveness
Instructions:
- Monitor for deer activity in first few days
- Adjust angle if deer approach from different direction
- Consider adding second unit for larger areas
- Clean solar panel monthly for optimal charging
- Check and adjust settings seasonally
Pro Tips:
- • Results typically seen within 1-3 days
- • Move device if deer find alternate routes
- • Winter: Brush snow off solar panel regularly
Optimal Placement Tips
Critical factors for maximum deer deterrent effectiveness
Optimal Height
Install 3-4 feet high for best deer detection
This height matches the typical eye level of adult deer, ensuring the sensor detects them reliably.
Solar Exposure
Ensure solar panel gets 4+ hours of direct sunlight daily
South-facing placement provides optimal charging. Even partial shade can reduce effectiveness.
Clear Line of Sight
Remove obstacles between sensor and protected area
Ultrasonic waves travel in straight lines and cannot penetrate dense vegetation or solid objects.
Detection Coverage
Position for 110° coverage of the most vulnerable areas
Place at corners or edges to maximize coverage area while protecting the most important zones.
Avoid Common Mistakes
Learn from others' experiences for optimal results
Mistake: Installing too low
Low placement may miss deer or trigger on small animals unnecessarily
Solution:
Mount at 3-4 feet height for optimal deer detection
Mistake: Blocked solar panel
Poor charging leads to battery drain and device failure
Solution:
Ensure panel faces south with no overhanging branches
Mistake: Obstructed sensor view
Reduced detection range and inconsistent activation
Solution:
Clear vegetation and obstacles from sensor path
Mistake: Wrong working mode
Single deterrent method may not be sufficient for persistent deer
Solution:
Use Mode 3 (ultrasonic + LED) for maximum effectiveness
Maintenance Schedule
Keep your deer repellent working at peak performance
Weekly
- Check for deer activity
- Verify LED activation during test walk
Monthly
- Clean solar panel with damp cloth
- Remove vegetation blocking sensor
Seasonally
- Adjust angle for seasonal deer patterns
- Check mounting stability
- Test all working modes
As Needed
- Brush snow off solar panel in winter
- Reposition if deer find alternate routes
Need Additional Help?
Our customer support team and comprehensive FAQ section are here to ensure your deer repellent installation is successful and effective.
Ready to Install Your Deer Protection?
Everything you need is included. Professional installation in just 5 minutes with our step-by-step guide and 30-day guarantee.